Special Price for Pneumatic On-Off Valve - ED Series Wafer butterfly valve – TWS Valve
Special Price for Pneumatic On-Off Valve - ED Series Wafer butterfly valve – TWS Valve Detail:
Description:
ED Series Wafer butterfly valve is soft sleeve type and can separate the body and fluid medium exactly,.
Material of Main Parts:
| Parts | Material |
| Body | CI,DI,WCB,ALB,CF8,CF8M |
| Disc | DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel |
| Stem | SS416,SS420,SS431,17-4PH |
| Seat | NBR,EPDM,Viton,PTFE |
| Taper Pin | SS416,SS420,SS431,17-4PH |
Seat Specification:
| Material | Temperature | Use Description |
| NBR | -23℃ ~ 82℃ | Buna-NBR:(Nitrile Butadiene Rubber ) has good tensile strength and resistance to abrasion.It is also resistant to hydrocarbon products.It is a good general-service material for use in water,vacuum,acid,salts,alkalines,fats,oils,greases,hydraulic oils and ethylene glycol. Buna-N can not use for acetone,ketones and nitrated or chlorinated hydrocarbons. |
| Shot time-23℃ ~120℃ | ||
| EPDM | -20 ℃~130℃ | General EPDM rubber: is a good general-service synthetic rubber used in hot-water, drinks, milk product systems and those containing ketones, alcohol, nitric ether esters and glycerol. But EPDM can not use for hydrocarbon based oils, minerals or solvents. |
| Shot time-30℃ ~ 150℃ | ||
| Viton | -10 ℃~ 180℃ | Viton is a fluorinated hydrocarbon elastomer with excellent resistance to most hydrocarbon oils and gases and other petroleum-based products. Viton can not use for steam service, hot water over 82℃ or concentrated alkalines. |
| PTFE | -5℃ ~ 110℃ | PTFE has good chemical performance stability and surface will be not sticky.At the same time, it has good lubricity property and aging resistance. It is a good material for use in acids, alkalis, oxidant and other corrodents. |
| (Inner liner EDPM) | ||
| PTFE | -5℃~90℃ | |
| (Inner liner NBR) |
Operation:lever,gearbox,electrical actuator,pneumatic actuator.
Characteristics:
1.Stem head design of Double “D” or Square cross:Convenient to connect with various actuators,deliver more torque;
2.Two piece stem square driver:No-space connection applies to any poor conditions;
3.Body without Frame structure:The seat can separate the body and fluid medium exactly,and convenient with pipe flange.
Dimension:
Product detail pictures:
Related Product Guide:
Special Price for Pneumatic On-Off Valve - ED Series Wafer butterfly valve – TWS Valve , The product will supply to all over the world, such as: , , ,
By from -
By from -
Related products
-
PriceList for Wafer Type Check Valve - RH Seri...
Description: RH Series Rubber seated swing check valve is simple, durable and exhibits improved design features over that of traditional metal-seated swing check valves. The disc and shaft are fully encapsulated with EPDM rubber to create the valve’s only moving part Characteristic: 1. Small in size&light in weight and easy maintenance. It can be mounted wherever needed. 2. Simple, compact structure, quick 90 degree on-off operation 3. Disc has two-way bearing, perfect seal, without leaka...
-
PriceList for Wafer Type Check Valve - BH Seri...
Description: BH Series Dual plate wafer check valve is the cost-effective backflow protection for piping systems,as it is the only fully elastomer-lined insert check valve.The valve body is completely isolated from line media which can extend the service life of this series in most appications and makes it an especially economical alternative in application which would othervise require check valve made of expensive alloys.. Characteristic: -Small in size, light in weight, compact in sturctur...
-
OEM China Soft Seated Butterfly Valve - UD Ser...
UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards should conform to butterfly valve standards; suggest using weldi...
-
Bottom price Flange Type Butterfly Valve - MD ...
Description: Comparing to our YD series,flange connection of MD Series wafer butterfly valve is specific,the handle is malleable iron. Working Temperature: •-45℃ to +135℃ for EPDM liner • -12℃ to +82℃ for NBR liner • +10℃ to +150℃ for PTFE liner Material of Main Parts: Parts Material Body CI,DI,WCB,ALB,CF8,CF8M Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel Stem SS416,SS420,SS431,17-4PH Seat NBR,EPDM,Viton,PTFE Taper Pin SS416,SS420,SS431,17-4PH Dimen...
-
Hot Selling for Seal Center Line Butterfly Valv...
Description: GD Series grooved end butterfly valve is a grooved end bubble tight shutoff butterfly valve with outstanding flow characteristics. The rubber seal is molded onto the ductile iron disc, in order to allow for maximum flow potential. It offers economical, efficient, and reliable service for grooved end piping applications. It is easily installed with two grooved end couplings. Typical application: HVAC, filtering system, etc. Dimensions: Size A B D D1 D2 L H E ...
-
Factory Promotional Flange End Type Butterfly V...
Description: YD Series Wafer butterfly valve ‘s flange connection is universal standard,and the material of handle is aluminium;It can be used as a device to cut-off or regulate the flow in various medium pipes. Through selecting different materials of disc and seal seat, as well as the pinless connection between disc and stem,the valve can be applied to worse conditions, such as desulphurization vacuum, sea water desalinization. Characteristic: 1. Small in size&light in weight and ...
