Rapid Delivery for Wafer Butterfly Valve Manufacturer - ED Series Wafer butterfly valve – TWS Valve
Rapid Delivery for Wafer Butterfly Valve Manufacturer - ED Series Wafer butterfly valve – TWS Valve Detail:
Description:
ED Series Wafer butterfly valve is soft sleeve type and can separate the body and fluid medium exactly,.
Material of Main Parts:
| Parts | Material |
| Body | CI,DI,WCB,ALB,CF8,CF8M |
| Disc | DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel |
| Stem | SS416,SS420,SS431,17-4PH |
| Seat | NBR,EPDM,Viton,PTFE |
| Taper Pin | SS416,SS420,SS431,17-4PH |
Seat Specification:
| Material | Temperature | Use Description |
| NBR | -23℃ ~ 82℃ | Buna-NBR:(Nitrile Butadiene Rubber ) has good tensile strength and resistance to abrasion.It is also resistant to hydrocarbon products.It is a good general-service material for use in water,vacuum,acid,salts,alkalines,fats,oils,greases,hydraulic oils and ethylene glycol. Buna-N can not use for acetone,ketones and nitrated or chlorinated hydrocarbons. |
| Shot time-23℃ ~120℃ | ||
| EPDM | -20 ℃~130℃ | General EPDM rubber: is a good general-service synthetic rubber used in hot-water, drinks, milk product systems and those containing ketones, alcohol, nitric ether esters and glycerol. But EPDM can not use for hydrocarbon based oils, minerals or solvents. |
| Shot time-30℃ ~ 150℃ | ||
| Viton | -10 ℃~ 180℃ | Viton is a fluorinated hydrocarbon elastomer with excellent resistance to most hydrocarbon oils and gases and other petroleum-based products. Viton can not use for steam service, hot water over 82℃ or concentrated alkalines. |
| PTFE | -5℃ ~ 110℃ | PTFE has good chemical performance stability and surface will be not sticky.At the same time, it has good lubricity property and aging resistance. It is a good material for use in acids, alkalis, oxidant and other corrodents. |
| (Inner liner EDPM) | ||
| PTFE | -5℃~90℃ | |
| (Inner liner NBR) |
Operation:lever,gearbox,electrical actuator,pneumatic actuator.
Characteristics:
1.Stem head design of Double “D” or Square cross:Convenient to connect with various actuators,deliver more torque;
2.Two piece stem square driver:No-space connection applies to any poor conditions;
3.Body without Frame structure:The seat can separate the body and fluid medium exactly,and convenient with pipe flange.
Dimension:
Product detail pictures:
Related Product Guide:
Rapid Delivery for Wafer Butterfly Valve Manufacturer - ED Series Wafer butterfly valve – TWS Valve , The product will supply to all over the world, such as: , , ,
By from -
By from -
Related products
-
New Fashion Design for Butterfly Valve Dn100 -...
Description: Comparing to our YD series,flange connection of MD Series wafer butterfly valve is specific,the handle is malleable iron. Working Temperature: •-45℃ to +135℃ for EPDM liner • -12℃ to +82℃ for NBR liner • +10℃ to +150℃ for PTFE liner Material of Main Parts: Parts Material Body CI,DI,WCB,ALB,CF8,CF8M Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel Stem SS416,SS420,SS431,17-4PH Seat NBR,EPDM,Viton,PTFE Taper Pin SS416,SS420,SS431,17-4PH Dimen...
-
Professional China Wafer Type Pinless Backed Se...
UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards should conform to butterfly valve standards; suggest using weldi...
-
OEM manufacturer Wcb Swing Check Valve - AH Se...
Description: Material list: No. Part Material AH EH BH MH 1 Body CI DI WCB CF8 CF8M C95400 CI DI WCB CF8 CF8M C95400 WCB CF8 CF8M C95400 2 Seat NBR EPDM VITON etc. DI Covered Rubber NBR EPDM VITON etc. 3 Disc DI C95400 CF8 CF8M DI C95400 CF8 CF8M WCB CF8 CF8M C95400 4 Stem 416/304/316 304/316 WCB CF8 CF8M C95400 5 Spring 316 …… Feature: Fasten Screw: Effectively prenvent the shaft from traveling,prevent valve work from failing and end from leaking. Body: Short face to f...
-
2021 China New Design Epdm Butterfly Valve - D...
Description: DL Series flanged concentric butterfly valve is with centric disc and bonded liner,and have all same common features of other wafer/lug series,these valves are featured by a higher strength of the body and better resistance to pipe pressures as safey factor. Having all same common features of the univisal series, these valves are featured by a higher strength of the body and better resistance to pipe pressures as safety factor. Characteristic: 1. Short Length pattern design 2. V...
-
Factory source Gate Valve Application - AZ Ser...
Description: AZ Series Resilient seated NRS gate valve is a wedge gate valve and Rising stem (Outside Screw and Yoke)type, and suitable for use with water and neutral liquids (sewage) . The OS&Y (Outside Screw and Yoke) gate valve is mainly used in fire protection sprinkler systems. The main difference from a standard NRS (Non Rising Stem) gate valve is that the stem and stem nut are placed outside the valve body. This makes it easy to see if the valve is open or closed, as almost the ent...
-
Manufacturer for Di Manual Butterfly Valve - E...
Description: ED Series Wafer butterfly valve is soft sleeve type and can separate the body and fluid medium exactly,. Material of Main Parts: Parts Material Body CI,DI,WCB,ALB,CF8,CF8M Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel Stem SS416,SS420,SS431,17-4PH Seat NBR,EPDM,Viton,PTFE Taper Pin SS416,SS420,SS431,17-4PH Seat Specification: Material Temperature Use Description NBR -23℃ ~ 82℃ Buna-NBR:(Nitrile Butadiene Rubber ) has good tensile st...
