Professional China Hydraulic Balancing Valve - TWS Flanged static balancing valve – TWS Valve
Professional China Hydraulic Balancing Valve - TWS Flanged static balancing valve – TWS Valve Detail:
Description:
TWS Flanged Static balancing valve is a key hydraulic balance product used for precise flow regulating of water pipelines system in HVAC application to ensure static hydraulic balance across whole water system. The series can ensure the actual flow of each terminal equipment and pipeline in line with the design flow in the phase of system initial commisiioning by site commissiong with flow measuring computer. The series are widely used in main pipes, branch pipes and terminal equipment pipelines in HVAC water system. It also can be use in other application with the same function requirement.
Features
Simplified pipe design and calculation
Quick and easy installation
Easy to measure and regulate water flowrate in site by the measuring computer
Easy to measure differential pressure in site
Balancing through stroke limitation with digital presetting and visible presetting display
Equipped with both pressure test cocks for differential pressure measurement Non rising hand wheel for convenience operation
Stroke limitation-screw protected by protection cap.
Valve stem made of stainless steel SS416
Cast iron body with corrosion resistant painting of epoxy powder
Applications:
HVAC water system
Installation
1.Read these instructions carefully. Failure to folow them could damage the product or cause a hazardous condition.
2.Check the ratings given in the instructions and on the product to make sure the product is suitable for your application.
3.Installer must be a trained, experienced service person.
4.Always conduct a thorough checkout when installation is completed.
5.For trouble-free operation of the product, good installation practice must include initial system flushing, chemical water treatment and the use of a 50 micron (or finer) system side stream filter(s). Remove all filters before flushing. 6.Suggest using a tentative pipe to do the initial system flushing. Then plumb the valve in the piping.
6.Do not use boiler additives, solder flux and wetted materials which are petroleum based or contain mineral oil, hydrocarbons, or ethylene glycol acetate. Compounds which can be used, with minimum 50% water dilution, are diethylene glycol, ethylene glycol, and propylene glycol (antifreeze solutions).
7.The valve may be installed with flow direction same as the arrow on the valve body. Wrong installation will lead to hydronic system paralysis.
8.A pair of test cocks attached in the packing case. Make sure it should be installed before initial commissioning and flushing. Make sure it isn’t damaged after installation.
Dimensions:
| DN | L | H | D | K | n*d |
| 65 | 290 | 364 | 185 | 145 | 4*19 |
| 80 | 310 | 394 | 200 | 160 | 8*19 |
| 100 | 350 | 472 | 220 | 180 | 8*19 |
| 125 | 400 | 510 | 250 | 210 | 8*19 |
| 150 | 480 | 546 | 285 | 240 | 8*23 |
| 200 | 600 | 676 | 340 | 295 | 12*23 |
| 250 | 730 | 830 | 405 | 355 | 12*28 |
| 300 | 850 | 930 | 460 | 410 | 12*28 |
| 350 | 980 | 934 | 520 | 470 | 16*28 |
Product detail pictures:
Related Product Guide:
Professional China Hydraulic Balancing Valve - TWS Flanged static balancing valve – TWS Valve , The product will supply to all over the world, such as: , , ,
By from -
By from -
Related products
-
Top Suppliers Watts Butterfly Valve - ED Serie...
Description: ED Series Wafer butterfly valve is soft sleeve type and can separate the body and fluid medium exactly,. Material of Main Parts: Parts Material Body CI,DI,WCB,ALB,CF8,CF8M Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel Stem SS416,SS420,SS431,17-4PH Seat NBR,EPDM,Viton,PTFE Taper Pin SS416,SS420,SS431,17-4PH Seat Specification: Material Temperature Use Description NBR -23℃ ~ 82℃ Buna-NBR:(Nitrile Butadiene Rubber ) has good tensile st...
-
Special Price for Pneumatic On-Off Valve - DL ...
Description: DL Series flanged concentric butterfly valve is with centric disc and bonded liner,and have all same common features of other wafer/lug series,these valves are featured by a higher strength of the body and better resistance to pipe pressures as safey factor. Having all same common features of the univisal series, these valves are featured by a higher strength of the body and better resistance to pipe pressures as safety factor. Characteristic: 1. Short Length pattern design 2. V...
-
Chinese Professional Pfa Butterfly Valve - DC ...
Description: DC Series flanged eccentric butterfly valve incorporates a positive retained resilient disc seal and either an integral body seat. The valve has three unique attributes: less weight, more strength and lower torque. Characteristic: 1. Eccentric action reduces torque and seat contact during operation extending valve life 2. Suitable for on/off and modulating service. 3. Subject to size and damage, the seat can be repaired in the field and in certain cases, repaired from outside the...
-
Wholesale Discount Butterfly Valve Epdm Seat -...
Description: GD Series grooved end butterfly valve is a grooved end bubble tight shutoff butterfly valve with outstanding flow characteristics. The rubber seal is molded onto the ductile iron disc, in order to allow for maximum flow potential. It offers economical, efficient, and reliable service for grooved end piping applications. It is easily installed with two grooved end couplings. Typical application: HVAC, filtering system, etc. Dimensions: Size A B D D1 D2 L H E...
-
Good User Reputation for Non Risng Stem - ED S...
Description: ED Series Wafer butterfly valve is soft sleeve type and can separate the body and fluid medium exactly,. Material of Main Parts: Parts Material Body CI,DI,WCB,ALB,CF8,CF8M Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel Stem SS416,SS420,SS431,17-4PH Seat NBR,EPDM,Viton,PTFE Taper Pin SS416,SS420,SS431,17-4PH Seat Specification: Material Temperature Use Description NBR -23℃ ~ 82℃ Buna-NBR:(Nitrile Butadiene Rubber ) has good tensile st...
-
High reputation Non-Return Check Valve - BH Se...
Description: BH Series Dual plate wafer check valve is the cost-effective backflow protection for piping systems,as it is the only fully elastomer-lined insert check valve.The valve body is completely isolated from line media which can extend the service life of this series in most appications and makes it an especially economical alternative in application which would othervise require check valve made of expensive alloys.. Characteristic: -Small in size, light in weight, compact in sturctur...
