OEM Factory for Kitz Butterfly Valve - ED Series Wafer butterfly valve – TWS Valve
OEM Factory for Kitz Butterfly Valve - ED Series Wafer butterfly valve – TWS Valve Detail:
Description:
ED Series Wafer butterfly valve is soft sleeve type and can separate the body and fluid medium exactly,.
Material of Main Parts:
| Parts | Material |
| Body | CI,DI,WCB,ALB,CF8,CF8M |
| Disc | DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel |
| Stem | SS416,SS420,SS431,17-4PH |
| Seat | NBR,EPDM,Viton,PTFE |
| Taper Pin | SS416,SS420,SS431,17-4PH |
Seat Specification:
| Material | Temperature | Use Description |
| NBR | -23℃ ~ 82℃ | Buna-NBR:(Nitrile Butadiene Rubber ) has good tensile strength and resistance to abrasion.It is also resistant to hydrocarbon products.It is a good general-service material for use in water,vacuum,acid,salts,alkalines,fats,oils,greases,hydraulic oils and ethylene glycol. Buna-N can not use for acetone,ketones and nitrated or chlorinated hydrocarbons. |
| Shot time-23℃ ~120℃ | ||
| EPDM | -20 ℃~130℃ | General EPDM rubber: is a good general-service synthetic rubber used in hot-water, drinks, milk product systems and those containing ketones, alcohol, nitric ether esters and glycerol. But EPDM can not use for hydrocarbon based oils, minerals or solvents. |
| Shot time-30℃ ~ 150℃ | ||
| Viton | -10 ℃~ 180℃ | Viton is a fluorinated hydrocarbon elastomer with excellent resistance to most hydrocarbon oils and gases and other petroleum-based products. Viton can not use for steam service, hot water over 82℃ or concentrated alkalines. |
| PTFE | -5℃ ~ 110℃ | PTFE has good chemical performance stability and surface will be not sticky.At the same time, it has good lubricity property and aging resistance. It is a good material for use in acids, alkalis, oxidant and other corrodents. |
| (Inner liner EDPM) | ||
| PTFE | -5℃~90℃ | |
| (Inner liner NBR) |
Operation:lever,gearbox,electrical actuator,pneumatic actuator.
Characteristics:
1.Stem head design of Double “D” or Square cross:Convenient to connect with various actuators,deliver more torque;
2.Two piece stem square driver:No-space connection applies to any poor conditions;
3.Body without Frame structure:The seat can separate the body and fluid medium exactly,and convenient with pipe flange.
Dimension:
Product detail pictures:
Related Product Guide:
OEM Factory for Kitz Butterfly Valve - ED Series Wafer butterfly valve – TWS Valve , The product will supply to all over the world, such as: , , ,
By from -
By from -
Related products
-
Hot sale Factory Butterfly Valve Tianjin - DC ...
Description: DC Series flanged eccentric butterfly valve incorporates a positive retained resilient disc seal and either an integral body seat. The valve has three unique attributes: less weight, more strength and lower torque. Characteristic: 1. Eccentric action reduces torque and seat contact during operation extending valve life 2. Suitable for on/off and modulating service. 3. Subject to size and damage, the seat can be repaired in the field and in certain cases, repaired from outside the...
-
OEM Customized Carbon Steel Check Valve - BH S...
Description: BH Series Dual plate wafer check valve is the cost-effective backflow protection for piping systems,as it is the only fully elastomer-lined insert check valve.The valve body is completely isolated from line media which can extend the service life of this series in most appications and makes it an especially economical alternative in application which would othervise require check valve made of expensive alloys.. Characteristic: -Small in size, light in weight, compact in sturctur...
-
Super Lowest Price Pneumatic Diaphragm Butterfl...
UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards should conform to butterfly valve standards; suggest using weldi...
-
Professional Design Hand Operated Butterfly Val...
Description: DL Series flanged concentric butterfly valve is with centric disc and bonded liner,and have all same common features of other wafer/lug series,these valves are featured by a higher strength of the body and better resistance to pipe pressures as safey factor. Having all same common features of the univisal series, these valves are featured by a higher strength of the body and better resistance to pipe pressures as safety factor. Characteristic: 1. Short Length pattern design 2. V...
-
Professional China Air Pressure Release Exhaust...
Description: The composite high-speed air release valve are combined with two parts of high-pressure diaphragm air valve and the low pressure inlet and exhaust valve ,It has both exhaust and intake functions. The high-pressure diaphragm air release valve automatically discharges the small amount of air accumulated in the pipeline when the pipeline is under pressure. The low-pressure intake and exhaust valve can not only discharge the air in the pipe when the empty pipe is filled with water, b...
-
Competitive Price for Full Lug Wafer Butterfly ...
UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards should conform to butterfly valve standards; suggest using weldi...
