High Quality Balancing Valve - TWS Flanged static balancing valve – TWS Valve
High Quality Balancing Valve - TWS Flanged static balancing valve – TWS Valve Detail:
Description:
TWS Flanged Static balancing valve is a key hydraulic balance product used for precise flow regulating of water pipelines system in HVAC application to ensure static hydraulic balance across whole water system. The series can ensure the actual flow of each terminal equipment and pipeline in line with the design flow in the phase of system initial commisiioning by site commissiong with flow measuring computer. The series are widely used in main pipes, branch pipes and terminal equipment pipelines in HVAC water system. It also can be use in other application with the same function requirement.
Features
Simplified pipe design and calculation
Quick and easy installation
Easy to measure and regulate water flowrate in site by the measuring computer
Easy to measure differential pressure in site
Balancing through stroke limitation with digital presetting and visible presetting display
Equipped with both pressure test cocks for differential pressure measurement Non rising hand wheel for convenience operation
Stroke limitation-screw protected by protection cap.
Valve stem made of stainless steel SS416
Cast iron body with corrosion resistant painting of epoxy powder
Applications:
HVAC water system
Installation
1.Read these instructions carefully. Failure to folow them could damage the product or cause a hazardous condition.
2.Check the ratings given in the instructions and on the product to make sure the product is suitable for your application.
3.Installer must be a trained, experienced service person.
4.Always conduct a thorough checkout when installation is completed.
5.For trouble-free operation of the product, good installation practice must include initial system flushing, chemical water treatment and the use of a 50 micron (or finer) system side stream filter(s). Remove all filters before flushing. 6.Suggest using a tentative pipe to do the initial system flushing. Then plumb the valve in the piping.
6.Do not use boiler additives, solder flux and wetted materials which are petroleum based or contain mineral oil, hydrocarbons, or ethylene glycol acetate. Compounds which can be used, with minimum 50% water dilution, are diethylene glycol, ethylene glycol, and propylene glycol (antifreeze solutions).
7.The valve may be installed with flow direction same as the arrow on the valve body. Wrong installation will lead to hydronic system paralysis.
8.A pair of test cocks attached in the packing case. Make sure it should be installed before initial commissioning and flushing. Make sure it isn’t damaged after installation.
Dimensions:
| DN | L | H | D | K | n*d |
| 65 | 290 | 364 | 185 | 145 | 4*19 |
| 80 | 310 | 394 | 200 | 160 | 8*19 |
| 100 | 350 | 472 | 220 | 180 | 8*19 |
| 125 | 400 | 510 | 250 | 210 | 8*19 |
| 150 | 480 | 546 | 285 | 240 | 8*23 |
| 200 | 600 | 676 | 340 | 295 | 12*23 |
| 250 | 730 | 830 | 405 | 355 | 12*28 |
| 300 | 850 | 930 | 460 | 410 | 12*28 |
| 350 | 980 | 934 | 520 | 470 | 16*28 |
Product detail pictures:
Related Product Guide:
High Quality Balancing Valve - TWS Flanged static balancing valve – TWS Valve , The product will supply to all over the world, such as: , , ,
By from -
By from -
Related products
-
Wholesale Price Motorized Gate Valve - WZ Seri...
Description: WZ Series Metal seated OS&Y gate valve use a ductile iron gate that houses bronze rings to ensure a watertight seal. The OS&Y (Outside Screw and Yoke) gate valve is mainly used in fire protection sprinkler systems. The main difference from a standard NRS (Non Rising Stem) gate valve is that the stem and stem nut are placed outside the valve body. This makes it easy to see if the valve is open or closed, as almost the entire length of the stem is visible when the valve is ...
-
Factory Cheap Hot Epoxy Coated Check Valve - E...
Description: EH Series Dual plate wafer check valve is with two torsion springs added to each of pair valve plates, which close the plates quickly and automatically, that can prevent the medium from flowing back.The check valve can be installed on both horizontal and vertical direction pipelines. Characteristic: -Small in size, light in weight, compact in sturcture, easy in maintenance. -Two torsion springs are added to each of the pair valve plates, which close the plates quickly and automat...
-
Factory Supply Swing Check Valve - AH Series D...
Description: Material list: No. Part Material AH EH BH MH 1 Body CI DI WCB CF8 CF8M C95400 CI DI WCB CF8 CF8M C95400 WCB CF8 CF8M C95400 2 Seat NBR EPDM VITON etc. DI Covered Rubber NBR EPDM VITON etc. 3 Disc DI C95400 CF8 CF8M DI C95400 CF8 CF8M WCB CF8 CF8M C95400 4 Stem 416/304/316 304/316 WCB CF8 CF8M C95400 5 Spring 316 …… Feature: Fasten Screw: Effectively prenvent the shaft from traveling,prevent valve work from failing and end from leaking. Body: Short face to f...
-
High Quality for Pneumatic Operated Butterfly V...
UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards should conform to butterfly valve standards; suggest using weldi...
-
OEM/ODM Manufacturer Non Rising Stem Metal Seat...
Description: WZ Series Metal seated NRS gate valve use a ductile iron gate that houses bronze rings to ensure a watertight seal. The non-rising stem design ensures the stem thread is adequately lubricated by the water passing through the valve. Application: Water supply system, water treatment, sewage disposal, food processing, fire protection system, natural gas, liquefied gas system etc. Dimensions: Type DN(mm) L D D1 b Z-Φd H D0 Weight (kg) NRS 40 165 150 110 18 4-Φ19 257 140 10/11 ...
-
Discount Price 10k Butterfly Valve - UD Series...
Description: UD Series hard seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Material of Main Parts: Parts Material Body CI,DI,WCB,ALB,CF8,CF8M Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel Stem SS416,SS420,SS431,17-4PH Seat NBR,EPDM,Viton,PTFE Taper Pin SS416,SS420,SS431,17-4PH Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation...
