High Quality Balancing Valve - TWS Flanged static balancing valve – TWS Valve

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

, , ,
High Quality Balancing Valve - TWS Flanged static balancing valve – TWS Valve Detail:

Description:

TWS Flanged Static balancing valve is a key hydraulic balance product used for precise flow regulating of water pipelines system in HVAC application to ensure static hydraulic balance across whole water system. The series can ensure the actual flow of each terminal equipment and pipeline in line with the design flow in the phase of system initial commisiioning by site commissiong with flow measuring computer. The series are widely used in main pipes, branch pipes and terminal equipment pipelines in HVAC water system. It also can be use in other application with the same function requirement.

Features

Simplified pipe design and calculation
Quick and easy installation
Easy to measure and regulate water flowrate in site by the measuring computer
Easy to measure differential pressure in site
Balancing through stroke limitation with digital presetting and visible presetting display
Equipped with both pressure test cocks for differential pressure measurement Non rising hand wheel for convenience operation
Stroke limitation-screw protected by protection cap.
Valve stem made of stainless steel SS416
Cast iron body with corrosion resistant painting of epoxy powder

Applications:

HVAC water system

Installation

1.Read these instructions carefully. Failure to folow them could damage the product or cause a hazardous condition.
2.Check the ratings given in the instructions and on the product to make sure the product is suitable for your application.
3.Installer must be a trained, experienced service person.
4.Always conduct a thorough checkout when installation is completed.
5.For trouble-free operation of the product, good installation practice must include initial system flushing, chemical water treatment and the use of a 50 micron (or finer) system side stream filter(s). Remove all filters before flushing. 6.Suggest using a tentative pipe to do the initial system flushing. Then plumb the valve in the piping.
6.Do not use boiler additives, solder flux and wetted materials which are petroleum based or contain mineral oil, hydrocarbons, or ethylene glycol acetate. Compounds which can be used, with minimum 50% water dilution, are diethylene glycol, ethylene glycol, and propylene glycol (antifreeze solutions).
7.The valve may be installed with flow direction same as the arrow on the valve body. Wrong installation will lead to hydronic system paralysis.
8.A pair of test cocks attached in the packing case. Make sure it should be installed before initial commissioning and flushing. Make sure it isn’t damaged after installation.

Dimensions:

20210927165122

DN L H D K n*d
65 290 364 185 145 4*19
80 310 394 200 160 8*19
100 350 472 220 180 8*19
125 400 510 250 210 8*19
150 480 546 285 240 8*23
200 600 676 340 295 12*23
250 730 830 405 355 12*28
300 850 930 460 410 12*28
350 980 934 520 470 16*28

Product detail pictures:

High Quality Balancing Valve - TWS Flanged static balancing valve – TWS Valve detail pictures


Related Product Guide:

High Quality Balancing Valve - TWS Flanged static balancing valve – TWS Valve , The product will supply to all over the world, such as: , , ,

  • 5 Stars By from -

    5 Stars By from -
    Write your message here and send it to us

    Related products

    • Best quality Resilient Gate Valve - WZ Series Metal seated OS&Y gate valve – TWS Valve

      Best quality Resilient Gate Valve - WZ Series ...

      Description: WZ Series Metal seated OS&Y gate valve use a ductile iron gate that houses bronze rings to ensure a watertight seal. The OS&Y (Outside Screw and Yoke) gate valve is mainly used in fire protection sprinkler systems. The main difference from a standard NRS (Non Rising Stem) gate valve is that the stem and stem nut are placed outside the valve body. This makes it easy to see if the valve is open or closed, as almost the entire length of the stem is visible when the valve is ...

    • OEM China En558-1 Check Valve - AH Series Dual plate wafer check valve – TWS Valve

      OEM China En558-1 Check Valve - AH Series Dual...

      Description: Material list: No. Part Material AH      EH BH MH 1 Body CI DI WCB CF8 CF8M C95400 CI DI WCB CF8 CF8M C95400 WCB CF8 CF8M C95400 2 Seat NBR EPDM VITON etc. DI Covered Rubber NBR EPDM VITON etc. 3 Disc DI C95400 CF8 CF8M DI C95400 CF8 CF8M WCB CF8 CF8M C95400 4 Stem 416/304/316 304/316 WCB CF8 CF8M C95400 5 Spring 316 …… Feature: Fasten Screw: Effectively prenvent the shaft from traveling,prevent valve work from failing and end from leaking. Body: Short face to f...

    • Factory wholesale Sea Water Check Valve - AH Series Dual plate wafer check valve – TWS Valve

      Factory wholesale Sea Water Check Valve - AH S...

      Description: Material list: No. Part Material AH      EH BH MH 1 Body CI DI WCB CF8 CF8M C95400 CI DI WCB CF8 CF8M C95400 WCB CF8 CF8M C95400 2 Seat NBR EPDM VITON etc. DI Covered Rubber NBR EPDM VITON etc. 3 Disc DI C95400 CF8 CF8M DI C95400 CF8 CF8M WCB CF8 CF8M C95400 4 Stem 416/304/316 304/316 WCB CF8 CF8M C95400 5 Spring 316 …… Feature: Fasten Screw: Effectively prenvent the shaft from traveling,prevent valve work from failing and end from leaking. Body: Short face to f...

    • Reasonable price Dual Check Valve - AH Series Dual plate wafer check valve – TWS Valve

      Reasonable price Dual Check Valve - AH Series ...

      Description: Material list: No. Part Material AH      EH BH MH 1 Body CI DI WCB CF8 CF8M C95400 CI DI WCB CF8 CF8M C95400 WCB CF8 CF8M C95400 2 Seat NBR EPDM VITON etc. DI Covered Rubber NBR EPDM VITON etc. 3 Disc DI C95400 CF8 CF8M DI C95400 CF8 CF8M WCB CF8 CF8M C95400 4 Stem 416/304/316 304/316 WCB CF8 CF8M C95400 5 Spring 316 …… Feature: Fasten Screw: Effectively prenvent the shaft from traveling,prevent valve work from failing and end from leaking. Body: Short face to f...

    • Fast delivery Epdm Seat Butterfly Valve - YD Series Wafer butterfly valve – TWS Valve

      Fast delivery Epdm Seat Butterfly Valve - YD S...

      Description: YD Series Wafer butterfly valve ‘s flange connection is universal standard,and the material of handle is aluminium;It can be used as a device to cut-off or regulate the flow in various medium pipes. Through selecting different materials of disc and seal seat, as well as the pinless connection between disc and stem,the valve can be applied to worse conditions, such as desulphurization vacuum, sea water desalinization. Characteristic: 1. Small in size&light in weight and ...

    • Factory source Double Flange Butterfly Valve - MD Series Wafer butterfly valve – TWS Valve

      Factory source Double Flange Butterfly Valve -...

      Description: Comparing to our YD series,flange connection of MD Series wafer butterfly valve is specific,the handle is malleable iron. Working Temperature: •-45℃ to +135℃ for EPDM liner • -12℃ to +82℃ for NBR liner • +10℃ to +150℃ for PTFE liner Material of Main Parts: Parts Material Body CI,DI,WCB,ALB,CF8,CF8M Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel Stem SS416,SS420,SS431,17-4PH Seat NBR,EPDM,Viton,PTFE Taper Pin SS416,SS420,SS431,17-4PH Dimens...