Good Quality Balance Valve - TWS Flanged static balancing valve – TWS Valve
Good Quality Balance Valve - TWS Flanged static balancing valve – TWS Valve Detail:
Description:
TWS Flanged Static balancing valve is a key hydraulic balance product used for precise flow regulating of water pipelines system in HVAC application to ensure static hydraulic balance across whole water system. The series can ensure the actual flow of each terminal equipment and pipeline in line with the design flow in the phase of system initial commisiioning by site commissiong with flow measuring computer. The series are widely used in main pipes, branch pipes and terminal equipment pipelines in HVAC water system. It also can be use in other application with the same function requirement.
Features
Simplified pipe design and calculation
Quick and easy installation
Easy to measure and regulate water flowrate in site by the measuring computer
Easy to measure differential pressure in site
Balancing through stroke limitation with digital presetting and visible presetting display
Equipped with both pressure test cocks for differential pressure measurement Non rising hand wheel for convenience operation
Stroke limitation-screw protected by protection cap.
Valve stem made of stainless steel SS416
Cast iron body with corrosion resistant painting of epoxy powder
Applications:
HVAC water system
Installation
1.Read these instructions carefully. Failure to folow them could damage the product or cause a hazardous condition.
2.Check the ratings given in the instructions and on the product to make sure the product is suitable for your application.
3.Installer must be a trained, experienced service person.
4.Always conduct a thorough checkout when installation is completed.
5.For trouble-free operation of the product, good installation practice must include initial system flushing, chemical water treatment and the use of a 50 micron (or finer) system side stream filter(s). Remove all filters before flushing. 6.Suggest using a tentative pipe to do the initial system flushing. Then plumb the valve in the piping.
6.Do not use boiler additives, solder flux and wetted materials which are petroleum based or contain mineral oil, hydrocarbons, or ethylene glycol acetate. Compounds which can be used, with minimum 50% water dilution, are diethylene glycol, ethylene glycol, and propylene glycol (antifreeze solutions).
7.The valve may be installed with flow direction same as the arrow on the valve body. Wrong installation will lead to hydronic system paralysis.
8.A pair of test cocks attached in the packing case. Make sure it should be installed before initial commissioning and flushing. Make sure it isn’t damaged after installation.
Dimensions:
| DN | L | H | D | K | n*d |
| 65 | 290 | 364 | 185 | 145 | 4*19 |
| 80 | 310 | 394 | 200 | 160 | 8*19 |
| 100 | 350 | 472 | 220 | 180 | 8*19 |
| 125 | 400 | 510 | 250 | 210 | 8*19 |
| 150 | 480 | 546 | 285 | 240 | 8*23 |
| 200 | 600 | 676 | 340 | 295 | 12*23 |
| 250 | 730 | 830 | 405 | 355 | 12*28 |
| 300 | 850 | 930 | 460 | 410 | 12*28 |
| 350 | 980 | 934 | 520 | 470 | 16*28 |
Product detail pictures:
Related Product Guide:
Good Quality Balance Valve - TWS Flanged static balancing valve – TWS Valve , The product will supply to all over the world, such as: , , ,
By from -
By from -
Related products
-
Manufacturing Companies for Double Check Backfl...
Description: BH Series Dual plate wafer check valve is the cost-effective backflow protection for piping systems,as it is the only fully elastomer-lined insert check valve.The valve body is completely isolated from line media which can extend the service life of this series in most appications and makes it an especially economical alternative in application which would othervise require check valve made of expensive alloys.. Characteristic: -Small in size, light in weight, compact in sturctur...
-
Manufacturing Companies for F4/F5 Gate Valve -...
Description: EZ Series Resilient seated OS&Y gate valve is a wedge gate valve and Rising stem type, and suitable for use with water and neutral liquids (sewage). Material: Parts Material Body Cast iron,Ductile iron Disc Ductilie iron&EPDM Stem SS416,SS420,SS431 Bonnet Cast iron,Ductile iron Stem nut Bronze Pressure test: Nominal pressure PN10 PN16 Test pressure Shell 1.5 Mpa 2.4 Mpa Sealing 1.1 Mpa 1.76 Mpa Operation: 1． Manual actuation In most cases,resi...
-
Popular Design for Soft Seal Butterfly Valve -...
Description: DL Series flanged concentric butterfly valve is with centric disc and bonded liner,and have all same common features of other wafer/lug series,these valves are featured by a higher strength of the body and better resistance to pipe pressures as safey factor. Having all same common features of the univisal series, these valves are featured by a higher strength of the body and better resistance to pipe pressures as safety factor. Characteristic: 1. Short Length pattern design 2. V...
-
Free sample for Genebre Butterfly Valve - BD S...
Description: BD Series wafer butterfly valve can be used as a device to cut-off or regulate the flow in various medium pipes. Through selecting different materials of disc and seal seat, as well as the pinless connection between disc and stem,the valve can be applied to worse conditions, such as desulphurization vacuum, sea water desalinization. Characteristic: 1. Small in size&light in weight and easy maintenance. It can be mounted wherever needed.2. Simple, compact structure, quick 90 ...
-
Personlized Products Single Flange Butterfly Va...
Description: GD Series grooved end butterfly valve is a grooved end bubble tight shutoff butterfly valve with outstanding flow characteristics. The rubber seal is molded onto the ductile iron disc, in order to allow for maximum flow potential. It offers economical, efficient, and reliable service for grooved end piping applications. It is easily installed with two grooved end couplings. Typical application: HVAC, filtering system, etc. Dimensions: Size A B D D1 D2 L H E ...
-
OEM/ODM China Combination Air Release Valve ...
Description: The composite high-speed air release valve are combined with two parts of high-pressure diaphragm air valve and the low pressure inlet and exhaust valve ,It has both exhaust and intake functions. The high-pressure diaphragm air release valve automatically discharges the small amount of air accumulated in the pipeline when the pipeline is under pressure. The low-pressure intake and exhaust valve can not only discharge the air in the pipe when the empty pipe is filled with water, b...
