Factory Supply Lug Type Concentric Butterfly Valve - ED Series Wafer butterfly valve – TWS Valve

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

, , ,
Factory Supply Lug Type Concentric Butterfly Valve - ED Series Wafer butterfly valve – TWS Valve Detail:

Description:

ED Series Wafer butterfly valve is soft sleeve type and can separate the body and fluid medium exactly,.

Material of Main Parts: 

Parts Material
Body CI,DI,WCB,ALB,CF8,CF8M
Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel
Stem SS416,SS420,SS431,17-4PH
Seat NBR,EPDM,Viton,PTFE
Taper Pin SS416,SS420,SS431,17-4PH

Seat Specification:

Material Temperature Use Description
NBR -23℃ ~ 82℃ Buna-NBR:(Nitrile Butadiene Rubber ) has good tensile strength and resistance to abrasion.It is also resistant to hydrocarbon products.It is a good general-service material for use in water,vacuum,acid,salts,alkalines,fats,oils,greases,hydraulic oils and ethylene glycol. Buna-N can not use for acetone,ketones and nitrated or chlorinated hydrocarbons.
Shot time-23℃ ~120℃
EPDM -20 ℃~130℃ General EPDM rubber: is a good general-service synthetic rubber used in hot-water, drinks, milk product systems and those containing ketones, alcohol, nitric ether esters and glycerol. But EPDM can not use for hydrocarbon based oils, minerals or solvents.
Shot time-30℃ ~ 150℃
Viton -10 ℃~ 180℃ Viton is a fluorinated hydrocarbon elastomer with excellent resistance to most hydrocarbon oils and gases and other petroleum-based products. Viton can not use for steam service, hot water over 82℃ or concentrated alkalines.
PTFE -5℃ ~ 110℃ PTFE has good chemical performance stability and surface will be not sticky.At the same time, it has good lubricity property and aging resistance. It is a good material for use in acids, alkalis, oxidant and other corrodents.
(Inner liner EDPM)
PTFE -5℃~90℃
(Inner liner NBR)

Operation:lever,gearbox,electrical actuator,pneumatic actuator.

Characteristics:

1.Stem head design of Double “D” or Square cross:Convenient to connect with various actuators,deliver more torque;

2.Two piece stem square driver:No-space connection applies to any poor conditions;

3.Body without Frame structure:The seat can separate the body and fluid medium exactly,and convenient with pipe flange.

Dimension:

20210927171813


Product detail pictures:

Factory Supply Lug Type Concentric Butterfly Valve - ED Series Wafer butterfly valve – TWS Valve detail pictures


Related Product Guide:

Factory Supply Lug Type Concentric Butterfly Valve - ED Series Wafer butterfly valve – TWS Valve , The product will supply to all over the world, such as: , , ,

  • 5 Stars By from -

    5 Stars By from -
    Write your message here and send it to us

    Related products

    • OEM/ODM China Gate Valve Handwheel - EZ Series  Resilient seated NRS gate valve – TWS Valve

      OEM/ODM China Gate Valve Handwheel - EZ Series...

      Description: EZ Series Resilient seated NRS gate valve is a wedge gate valve and Non-rising stem type, and suitable for use with water and neutral liquids (sewage). Characteristic: -On-line replacement of top seal: Easy installation and maintenance. -Integral rubber-clad disc: The ductile iron frame work is thermal-clad integrally with high performance rubber. Ensuring tight seal and rust prevention. -Integrated brass nut: By means of special casting process. the brass stem nut is integrated ...

    • Hot New Products Ductile Iron Air Valve - TWS Air release valve – TWS Valve

      Hot New Products Ductile Iron Air Valve - TWS ...

      Description: The composite high-speed air release valve are combined with two parts of high-pressure diaphragm air valve and the low pressure inlet and exhaust valve ,It has both exhaust and intake functions. The high-pressure diaphragm air release valve automatically discharges the small amount of air accumulated in the pipeline when the pipeline is under pressure. The low-pressure intake and exhaust valve can not only discharge the air in the pipe when the empty pipe is filled with water, b...

    • factory Outlets for Rubber Seal Butterfly Valve - UD Series soft sleeve seated butterfly valve – TWS Valve

      factory Outlets for Rubber Seal Butterfly Valve...

      UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards should conform to butterfly valve standards; suggest using weldi...

    • OEM/ODM Supplier Dn 80 Cast Iron Gate Valve - EZ Series  Resilient seated NRS gate valve – TWS Valve

      OEM/ODM Supplier Dn 80 Cast Iron Gate Valve - ...

      Description: EZ Series Resilient seated NRS gate valve is a wedge gate valve and Non-rising stem type, and suitable for use with water and neutral liquids (sewage). Characteristic: -On-line replacement of top seal: Easy installation and maintenance. -Integral rubber-clad disc: The ductile iron frame work is thermal-clad integrally with high performance rubber. Ensuring tight seal and rust prevention. -Integrated brass nut: By means of special casting process. the brass stem nut is integrated ...

    • 2021 Good Quality Stainless Steel Y Type Strainer - TWS Flanged Y Strainer According to ANSI B16.10 – TWS Valve

      2021 Good Quality Stainless Steel Y Type Strain...

      Description: Y strainers mechanically remove solids from flowing steam, gases or liquid piping systems with the use of a perforated or wire mesh straining screen, and are used to protect equipment. From a simple low pressure cast iron threaded strainer to a large, high pressure special alloy unit with a custom cap design. Material list:  Parts Material Body Cast iron Bonnet Cast iron Filtering net Stainless steel Feature: Unlike other types of strainers, a Y-Strainer has the advan...

    • OEM Customized Electric Gate Valve -  WZ Series Metal seated OS&Y gate valve – TWS Valve

      OEM Customized Electric Gate Valve - WZ Serie...

      Description: WZ Series Metal seated OS&Y gate valve use a ductile iron gate that houses bronze rings to ensure a watertight seal. The OS&Y (Outside Screw and Yoke) gate valve is mainly used in fire protection sprinkler systems. The main difference from a standard NRS (Non Rising Stem) gate valve is that the stem and stem nut are placed outside the valve body. This makes it easy to see if the valve is open or closed, as almost the entire length of the stem is visible when the valve is ...