Factory Cheap Hot China Balancing Valve - TWS Flanged static balancing valve – TWS Valve

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

, , ,
Factory Cheap Hot China Balancing Valve - TWS Flanged static balancing valve – TWS Valve Detail:

Description:

TWS Flanged Static balancing valve is a key hydraulic balance product used for precise flow regulating of water pipelines system in HVAC application to ensure static hydraulic balance across whole water system. The series can ensure the actual flow of each terminal equipment and pipeline in line with the design flow in the phase of system initial commisiioning by site commissiong with flow measuring computer. The series are widely used in main pipes, branch pipes and terminal equipment pipelines in HVAC water system. It also can be use in other application with the same function requirement.

Features

Simplified pipe design and calculation 
Quick and easy installation 
Easy to measure and regulate water flowrate in site by the measuring computer
Easy to measure differential pressure in site 
Balancing through stroke limitation with digital presetting and visible presetting display 
Equipped with both pressure test cocks for differential pressure measurement Non rising hand wheel for convenience operation 
Stroke limitation-screw protected by protection cap. 
Valve stem made of stainless steel SS416 
Cast iron body with corrosion resistant painting of epoxy powder

Applications:

HVAC water system

Installation

1.Read these instructions carefully. Failure to folow them could damage the product or cause a hazardous condition.
2.Check the ratings given in the instructions and on the product to make sure the product is suitable for your application.
3.Installer must be a trained, experienced service person.
4.Always conduct a thorough checkout when installation is completed.
5.For trouble-free operation of the product, good installation practice must include initial system flushing, chemical water treatment and the use of a 50 micron (or finer) system side stream filter(s). Remove all filters before flushing. 6.Suggest using a tentative pipe to do the initial system flushing. Then plumb the valve in the piping.
6.Do not use boiler additives, solder flux and wetted materials which are petroleum based or contain mineral oil, hydrocarbons, or ethylene glycol acetate. Compounds which can be used, with minimum 50% water dilution, are diethylene glycol, ethylene glycol, and propylene glycol (antifreeze solutions).
7.The valve may be installed with flow direction same as the arrow on the valve body. Wrong installation will lead to hydronic system paralysis.
8.A pair of test cocks attached in the packing case. Make sure it should be installed before initial commissioning and flushing. Make sure it isn’t damaged after installation.

Dimensions:

20210927165122

DN L H D K n*d
65 290 364 185 145 4*19
80 310 394 200 160 8*19
100 350 472 220 180 8*19
125 400 510 250 210 8*19
150 480 546 285 240 8*23
200 600 676 340 295 12*23
250 730 830 405 355 12*28
300 850 930 460 410 12*28
350 980 934 520 470 16*28

Product detail pictures:

Factory Cheap Hot China Balancing Valve - TWS Flanged static balancing valve – TWS Valve detail pictures


Related Product Guide:

Factory Cheap Hot China Balancing Valve - TWS Flanged static balancing valve – TWS Valve , The product will supply to all over the world, such as: , , ,

  • 5 Stars By from -

    5 Stars By from -
    Write your message here and send it to us

    Related products

    • OEM Factory for Cast Iron Wafer Check Valve - BH Series Dual plate wafer check valve – TWS Valve

      OEM Factory for Cast Iron Wafer Check Valve - ...

      Description: BH Series Dual plate wafer check valve is the cost-effective backflow protection for piping systems,as it is the only fully elastomer-lined insert check valve.The valve body is completely isolated from line media which can extend the service life of this series in most appications and makes it an especially economical alternative in application which would othervise require check valve made of expensive alloys.. Characteristic: -Small in size, light in weight, compact in sturctur...

    • OEM/ODM Factory Abo Butterfly Valve - GD Series grooved end butterfly valve – TWS Valve

      OEM/ODM Factory Abo Butterfly Valve - GD Serie...

      Description: GD Series grooved end butterfly valve is a grooved end bubble tight shutoff butterfly valve with outstanding flow characteristics. The rubber seal is molded onto the ductile iron disc, in order to allow for maximum flow potential. It offers economical, efficient, and reliable service for grooved end piping applications. It is easily installed with two grooved end couplings. Typical application: HVAC, filtering system, etc. Dimensions: Size A B D D1 D2 L H E...

    • Factory Outlets Butterfly Valve With Spindle - UD Series soft sleeve seated butterfly valve – TWS Valve

      Factory Outlets Butterfly Valve With Spindle -...

      UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards should conform to butterfly valve standards; suggest using weldi...

    • Factory directly Pneumatic Dust Butterfly Valve - MD Series Lug butterfly valve – TWS Valve

      Factory directly Pneumatic Dust Butterfly Valve...

      Description: MD Series Lug type butterfly valve allows downstream pipelines and equipments online repair, and it can be installed on pipe ends as exhaust valve. Alignment features of lugged body allows easy installation between pipeline flanges. a real installationi cost saving, can be installed in the pipe end. Characteristic: 1. Small in size&light in weight and easy maintenance. It can be mounted wherever needed. 2. Simple, compact structure, quick 90 degree on-off operation 3. Disc ha...

    • Cheap PriceList for Non Rising Stem Gate Valve - WZ Series Metal seated OS&Y gate valve – TWS Valve

      Cheap PriceList for Non Rising Stem Gate Valve ...

      Description: WZ Series Metal seated OS&Y gate valve use a ductile iron gate that houses bronze rings to ensure a watertight seal. The OS&Y (Outside Screw and Yoke) gate valve is mainly used in fire protection sprinkler systems. The main difference from a standard NRS (Non Rising Stem) gate valve is that the stem and stem nut are placed outside the valve body. This makes it easy to see if the valve is open or closed, as almost the entire length of the stem is visible when the valve is ...

    • Newly Arrival Electric Resilient Seated - MD Series Lug butterfly valve – TWS Valve

      Newly Arrival Electric Resilient Seated - MD S...

      Description: MD Series Lug type butterfly valve allows downstream pipelines and equipments online repair, and it can be installed on pipe ends as exhaust valve. Alignment features of lugged body allows easy installation between pipeline flanges. a real installationi cost saving, can be installed in the pipe end. Characteristic: 1. Small in size&light in weight and easy maintenance. It can be mounted wherever needed. 2. Simple, compact structure, quick 90 degree on-off operation 3. Disc ha...