2021 China New Design China Flow Balancing Valve – TWS Flanged static balancing valve – TWS Valve

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

, , ,
2021 China New Design China Flow Balancing Valve – TWS Flanged static balancing valve – TWS Valve Detail:

Description:

TWS Flanged Static balancing valve is a key hydraulic balance product used for precise flow regulating of water pipelines system in HVAC application to ensure static hydraulic balance across whole water system. The series can ensure the actual flow of each terminal equipment and pipeline in line with the design flow in the phase of system initial commisiioning by site commissiong with flow measuring computer. The series are widely used in main pipes, branch pipes and terminal equipment pipelines in HVAC water system. It also can be use in other application with the same function requirement.

Features

Simplified pipe design and calculation 
Quick and easy installation 
Easy to measure and regulate water flowrate in site by the measuring computer
Easy to measure differential pressure in site 
Balancing through stroke limitation with digital presetting and visible presetting display 
Equipped with both pressure test cocks for differential pressure measurement Non rising hand wheel for convenience operation 
Stroke limitation-screw protected by protection cap. 
Valve stem made of stainless steel SS416 
Cast iron body with corrosion resistant painting of epoxy powder

Applications:

HVAC water system

Installation

1.Read these instructions carefully. Failure to folow them could damage the product or cause a hazardous condition.
2.Check the ratings given in the instructions and on the product to make sure the product is suitable for your application.
3.Installer must be a trained, experienced service person.
4.Always conduct a thorough checkout when installation is completed.
5.For trouble-free operation of the product, good installation practice must include initial system flushing, chemical water treatment and the use of a 50 micron (or finer) system side stream filter(s). Remove all filters before flushing. 6.Suggest using a tentative pipe to do the initial system flushing. Then plumb the valve in the piping.
6.Do not use boiler additives, solder flux and wetted materials which are petroleum based or contain mineral oil, hydrocarbons, or ethylene glycol acetate. Compounds which can be used, with minimum 50% water dilution, are diethylene glycol, ethylene glycol, and propylene glycol (antifreeze solutions).
7.The valve may be installed with flow direction same as the arrow on the valve body. Wrong installation will lead to hydronic system paralysis.
8.A pair of test cocks attached in the packing case. Make sure it should be installed before initial commissioning and flushing. Make sure it isn’t damaged after installation.

Dimensions:

20210927165122

DN L H D K n*d
65 290 364 185 145 4*19
80 310 394 200 160 8*19
100 350 472 220 180 8*19
125 400 510 250 210 8*19
150 480 546 285 240 8*23
200 600 676 340 295 12*23
250 730 830 405 355 12*28
300 850 930 460 410 12*28
350 980 934 520 470 16*28

Product detail pictures:

2021 China New Design China Flow Balancing Valve – TWS Flanged static balancing valve – TWS Valve detail pictures


Related Product Guide:

2021 China New Design China Flow Balancing Valve – TWS Flanged static balancing valve – TWS Valve , The product will supply to all over the world, such as: , , ,

  • 5 Stars By from -

    5 Stars By from -
    Write your message here and send it to us

    Related products

    • Discountable price Butterfly Valve Actuator - UD Series soft sleeve seated butterfly valve – TWS Valve

      Discountable price Butterfly Valve Actuator - ...

      UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards should conform to butterfly valve standards; suggest using weldi...

    • Rapid Delivery for Wafer Butterfly Valve Manufacturer - DL Series flanged concentric butterfly valve – TWS Valve

      Rapid Delivery for Wafer Butterfly Valve Manufa...

      Description: DL Series flanged concentric butterfly valve is with centric disc and bonded liner,and have all same common features of other wafer/lug series,these valves are featured by a higher strength of the body and better resistance to pipe pressures as safey factor. Having all same common features of the univisal series, these valves are featured by a higher strength of the body and better resistance to pipe pressures as safety factor.  Characteristic: 1. Short Length pattern design 2. V...

    • Manufacturer of Danfoss Butterfly Valve - FD Series Wafer butterfly valve – TWS Valve

      Manufacturer of Danfoss Butterfly Valve - FD S...

      Description: FD Series Wafer butterfly valve with PTFE lined structure, this series resilient seated butterfly valve is designed for corrosive media, especially various kinds of strong acids, such as sulfuric acid and aqua regia. The PTFE material will not pollute media within a pipeline. Characteristic: 1. The butterfly valve comes with two-way installation, zero leakage, corrosion resistance, light weight, small size, low cost and easy installation.2. Tts PTFE clad seat is capable of protec...

    • Reasonable price Dual Check Valve - EH Series Dual plate wafer check valve – TWS Valve

      Reasonable price Dual Check Valve - EH Series ...

      Description: EH Series Dual plate wafer check valve is with two torsion springs added to each of pair valve plates, which close the plates quickly and automatically, that can prevent the medium from flowing back.The check valve can be installed on both horizontal and vertical direction pipelines. Characteristic: -Small in size, light in weight, compact in sturcture, easy in maintenance. -Two torsion springs are added to each of the pair valve plates, which close the plates quickly and automat...

    • Manufacturing Companies for Hawle Butterfly Valve - DC Series flanged eccentric butterfly valve – TWS Valve

      Manufacturing Companies for Hawle Butterfly Val...

      Description: DC Series flanged eccentric butterfly valve incorporates a positive retained resilient disc seal and either an integral body seat. The valve has three unique attributes: less weight, more strength and lower torque. Characteristic: 1. Eccentric action reduces torque and seat contact during operation extending valve life 2. Suitable for on/off and modulating service. 3. Subject to size and damage, the seat can be repaired in the field and in certain cases, repaired from outside the...

    • Reasonable price Ansi Gate Valve - EZ Series  Resilient seated NRS gate valve – TWS Valve

      Reasonable price Ansi Gate Valve - EZ Series ...

      Description: EZ Series Resilient seated NRS gate valve is a wedge gate valve and Non-rising stem type, and suitable for use with water and neutral liquids (sewage). Characteristic: -On-line replacement of top seal: Easy installation and maintenance. -Integral rubber-clad disc: The ductile iron frame work is thermal-clad integrally with high performance rubber. Ensuring tight seal and rust prevention. -Integrated brass nut: By means of special casting process. the brass stem nut is integrated...